noscriptMechanical Hazard Gloves | Cromwell Tools

Mechanical Hazard Gloves

What are mechanical hazard gloves?

Mechanical hazard gloves are defined by their compliance to the standard EN 388:2016 - Protective Gloves Against Mechanical Risks. EN 388 was first published in 1994 and subsequently revised in 2003, and again in 2016.

It includes the testing assessment of the resistance of the palm area to mild abrasion, cut, tearing and puncture, and when required, impact protection. If tests are not performed or are not applicable, 'X' will be placed instead of a number/letter.

Abrasion resistance test EN 388

When compared with EN 388:2003, there is a technical change to the abrasion resistance
method for EN388:2016, relating to the choice of abrasive paper but the scores that can be achieved remain unchanged. The scores are from 1 - 4, with 4 being the highest score being able to be achieved.

Abrasion resistance is tested by the number of cycles that the paper does before inflicting damage upon the gloves. Level 1 is 100 cycles, level 2 is 500 cycles, level 3 is 1000 cycles and level 4 is 8000 cycles.

Cut resistance tests EN388

With regards to cut, there is the original coupe test, and in 2016 there was the introduction of the Tomodynamometer (TDM-100 or TDM) cut test under EN ISO 3997.

The initial thought was that the TDM test would supersede the original coupe test, but this is now not the case, and both will remain as applicable tests.

However, it is important to note that the tests are completely different, and the result scores do not correlate with each other.

The Coupe (Circular Blade) test is a circular rotating blade and results are based the number of cycles the machine completes before cutting through the fabric.

It was initially thought that the coupe test would be made redundant and the TDM
test take precedence. We do understand now that both tests will remain but there
have been changes to the coupe test from the 2003 version to the now 2016 version.

The test has been updated from a technical standpoint for it to remain as one of
the cut test options.

The score given, after achieving a certain test result using this method, remains from 1 - 5, with 5 being the highest rating to be achieved.

The Tomodynamometer (TDM) test, also referred to as the TDM-100 test is a straight blade, and the test is based on the vertical
force applied in newtons until cut through takes place.

The force and cut-through length are plotted on a graph and a trend line is generated. The identified force is applied to the specimen a further five times.

If the results of the stroke length are within the tolerance levels, the test is then complete, and the force has been determined
and given a score from A - F, F being the highest score.

It is important to note that each blade is only used once for the test, and that as it is a straight blade.

It is widely thought of to be a test with more similarities to real world applications and more comparable to potential cut hazards
and risks in the workplace.

Usually there is an "X" which denotes that a test has not been undertaken or alternatively, in the case of the TDM cut test, there may no marking shown on the glove or documents at all.

Tear resistance test EN388

In this test, specimens of material from the palm of four gloves and clamped in the jaws of a standard tensile strength testing machine.

The jaws are moved apart at a constant speed (100mm/min), and the force (in newtons) needed to tear the material is measured. The scores are from 1 - 4, with 4 being the highest score being able to be achieved.

Puncture resistance test EN388

The test uses a rounded object which is pushed 50mm into the specimen at a constant speed of 100mm/min using a compression test machine. The maximum resistance force (in newtons) is recorded.

Performance levels are based on the lowest of four test results. The scores are from 1 - 4, with 4 being the highest score being able to be achieved.

It is important to note that this test would not replicate the puncture resistance needed to protect against potential needlestick risks.

There is currently no standard for the testing of hypodermic needles with hand protection. We (the UK) currently align ourselves with the American ANSI standard, ASTM F2878, as there haven't been a UK equivalent.

However, this is under review as we anticipate a needlestick test will make it into future revisions of EN 388. As your safety provider as soon as we are informed of such additions we will update this guide to reflect.

Impact resistance EN388

This is a test that was not included in EN 388:2003, and is used for gloves which incorporate specific impact-resistant properties which may be added to the palm, back of the hand or the knuckles.

The test area is impacted with a 2.5kg flat face striker from a sufficient height to
provide impact energy of 5J. The peak force which is detected by a sensor is recorded. Four tests are carried out on specimens of each area of protection taken from four different gloves. The test result is either a Pass "P" or Fail "X", or alternatively, there may no marking shown on the glove or documents at all.

Sort By:
Most Popular

Rows per page:

10

1-10 of 983

Rows per page:

10

1-10 of 983